Expert Answers about Chevrolet Trailer Hitch Ball

• What is the Difference Between a Class I and Class II Ball Mount
• Class I Ball Mounts When towing with a Class I trailer hitch, the Class I ball mount that is recommended by the trailer hitch manufacturer should be used. All Class I trailer hitches are tested and rated with the specific ball mount for that hitch. Using a ball mount that is not recommended by the manufacturer will void the warranty. The features of a a Class I ball mount are: Has a 1-1/4 inch x 1-1/4 inch shank Class II ball mounts will not fit on Class I trailer hitches Held in place...
  view full answer...


• What Are The Differences Between Standard Trailer Hitch And Gooseneck Hitch Balls
• The size of the hitch ball itself is the same but there are differences between the standard hitch balls and a gooseneck ball. The shank on a standard hitch ball like the hitch ball you came from, part # BWHB94005, is threaded so that the nut can be used to tighten it to the balll mount. On a gooseneck ball they are typically designed to fit a specific gooseneck hitch. For example, a hitch ball for a B&W Turnover Gooseneck Hitch like part # BWGNXA2005 has a square shank that is a specific...
  view full answer...


• Aluminum Ball Mount Selection For 2005 Jeep Liberty
• A difference in length of your hitch, or ball mount will effect the clearance from the trailer to the rear of your Jeep Liberty. What you would want to do is measure the clearance needed on your Jeep Liberty. To measure the clearance needed, you will want to measure from the center of the hitch pin hole out 8-1/4 Inches. This will be the location of your hitch ball. Then what you can do is move your trailer and position the coupler to that approximate location to see if there will be any...
  view full answer...


• What is the Difference Between the Hidden Hitch and Draw-Tite Trailer Hitch for a 2011 Mustang GT
• The only difference between the Draw-Tite Sportframe Class I Trailer Hitch, # 24863, and the Hidden Hitch Class I Trailer Hitch, # 60280 (no longer available), is that the Hidden Hitch Trailer Hitch includes a ball mount. Draw-Tite and Hidden Hitch are sister companies that use the same design, specifications and materials for their products. The only advantage to purchasing one over the other is that you will get a ball mount with the Hidden Hitch trailer hitch. In this case you will...
  view full answer...


• Comparison Of Trailer Hitches For 2002 Chevrolet Suburban
• Both of the trailer hitches you mentioned are a great fit for your 2002 Chevrolet Suburban. The Curt Hitch, part # 14080 is a Class lV hitch and it has a 2-inch receiver opening. The Draw-Tite hitch, part # 41930 is a Class V hitch and it also has a 2-inch receiver opening. Both hitches have identical towing capacity and weight distribution capacity. If it makes a difference to you, the Curt hitch is manufactured in the USA. If you plan on doing some towing you might be interested...
  view full answer...


• Difference In Draw-Tite Class IV Hitch Compared To Lower Priced Class IV Hitch
• When comparing the Draw-Tite Ultra Frame Trailer Hitch Receiver - Class IV, part # 41929, to the Curt Trailer Hitch Receiver - Class IV, part # 14361, they are similar, but the new version of the Draw-Tite # 41929 is rated higher. The Draw-Tite Class IV Hitch has a tongue weight capacity of 1,200 pounds and towing capacity of 12,000 pounds. The Curt Class IV Hitch has a tongue weight capacity of 1,000 pounds, and towing capacity of 10,000 pounds. Both part # 41929, and part # 14361 have...
  view full answer...


• Are the Draw Tite and Hidden Hitch for 2003 Toyota 4Runner the Same Hitch
• Yes, the Hidden Hitch part # 70779 and the Draw Tite # 75155 are the exact same hitch as they are both made by the same parent company Cequent. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not include a ball mount...
  view full answer...


• Why is Curt Hitch Ball # 40038 w/ 12,000 LB GTW Shank Diameter Smaller Than Husky Ball w/ 8,000 LB
• I spoke with my contact at Curt and numerous factors go into the capacity of a hitch ball, including the way the shank is threaded as well as the way the metal was finished. The Curt Hitch Ball, # 40038, has been tested and has a 12,000 lb towing capacity. You definitely want to use a hitch ball that is rated high enough for the weight of your horse trailer and part # 40038 would cover this. Although the Husky ball looks to be sturdier, you mention that it only has an 8,000 lb capacity...
  view full answer...


• Trailer Part Difference Between 2010 VW Jetta Sedan and Sportwagen Models
• Yes. There is a difference in the fit for a 2010 Jetta Sedan compared to the Jetta Sportwagen. For a 2010 Jetta Sedan, I recommend the Curt # C11474 for a trailer hitch, the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118667 (which connects behind tail lights), and ball mount # 3593. Then you can use hitch ball # 19256 for a 1-7/8 inch diameter ball or # 19258 for a 2 inch ball. For a 2010 Jetta Sportwagen, the frame is the same so the hitch will be the same but...
  view full answer...


• Selecting a Cushioned Ball Mount Capable of a 3" Drop Which Fits a 2" Hitch Receiver
• I have a few options depending on the amount you will be towing and how adjustable you want to hitch to be for other trailers. First is the Curt RockerBall Anti-Rattle Towing Kit # C63KR. This uses a standard style ball mount with a cushioned 2" hitch ball. This will be set at the 3" height and is not adjustable but is the most economical of the choices. The Gen-Y Glyder Shock Absorbing Ball Mount # 325-GH-12005 is a cushioned mount. It does allow you to bolt the bracket from a 0-6" drop...
  view full answer...


• Difference Between Curt 13534 and etrailer Brand e98858 Class III Hitch for2008 Toyota Highlander
• Other than the fact that the Curt # 13534 uses a gloss powder coat finish and the etrailer.com brand # e98858 hitch uses a matte finish powder coat, there's no difference between the two hitches. Curt manufactures the etrailer.com brand hitches for us, so you know it's a high quality product. If you'll be using the hitch for towing purposes, you'll also need a trailer wiring harness, a ball mount and a trailer ball to complete your towing setup. For a wiring harness, use part # 118449,...
  view full answer...


• comparing Curt Class III and IV Trailer Hitches for a 2001 Ford F-150
• The main difference between the Curt trailer hitch # C14355 and hitch # 13355, is capacity. Both hitches feature a 2 inch receiver. Both hitches will fit on your truck if it has a 20 inch or smaller spare tire. But the key is the weight capacity of each hitch. The Class IV trailer hitch, # C14355, has a tongue weight capacity of 1,000 pounds, and a gross trailer weight capacity of 10,000 pounds. When used with weight distribution, those ratings increase to 1,200/12,000 pounds. Keep in...
  view full answer...


• Comparing Curt Trailer Hitches for a 2014 GMC Sierra 1500
• The mounting holes are slightly different between Curt trailer hitch # C14006 and # 14301. I have included a side by side picture that shows this. Otherwise they have the same capacities. I have linked instructions for both hitch for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # EBMK2416. It comes with a ball mount with a 3 inch rise or 4 inch drop, a 2 inch and 2-5/16 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit...
  view full answer...


• Comparing Plugs for B&W Turnoverball Gooseneck Trailer Hitch
• There are two different plugs for the B&W Turnoverball Gooseneck Trailer Hitch, the part # BWGNXA1710 which attaches to the hitch ball assembly and covers the opening in the bed while the hitch ball is in the stowed position and the part # BWGNXA1715 which covers the opening in the bed with the hitch ball assembly removed. These are the only two plugs that B&W offers for the B&W Turnoverball Gooseneck Trailer Hitch.
  view full answer...


• Comparing the Curt and Draw-Tite Trailer Hitches for a 2020 Land Rover Range Rover Sport
• The Draw-Tite Max-Frame Trailer Hitch Receiver part # 75229 and Curt Trailer Hitch Receiver part # C13243 are both excellent options for a 2020 Land Rover Range Rover Sport. I recommend the Curt Trailer Hitch because there will be less modifications required for installation and in my personal experience the finish and fit is a tad better than that of the Draw-Tite Hitch. The Curt Trailer Hitch has a hidden design so only the required receiver will be visible from outside the vehicle. In...
  view full answer...


• Comparing The Available Trailer Hitches For A 2008 Cadillac CTS
• All of the hitches available for the 2008 Cadillac CTS have the same characteristics in terms of towing and tongue weight capacity. Each hitch has a 2000 pound towing capacity and 200 pound tongue weight capacity. Where they differ is the towing components included with the hitch. The Draw-Tite Trailer Hitch, part # 24767, which is the lower priced hitch, does not include a drawbar, pin or clip. The Curt Hitch, part # 11307, which is the highest priced hitch for your vehicle includes a...
  view full answer...


• What Is the Difference Between the EcoHitch and Stealth Hitch for the 2020 Subaru Crosstrek
• The difference between the EcoHitch # 306-X7365 and the Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit - Custom Fit - 2" # 391SUCT18T is that the Stealth hitch comes with everything you'd need to tow a trailer including the hitch ball and ball mount, as well as the trailer wiring harness. The 2020 Subaru Crosstrek only has a 200-lbs tongue weight capacity and a 1500-lbs towing capacity and you're always limited by the lowest rated component in your towing setup; in this case...
  view full answer...


• Comparing Draw-Tite Trailer Hitches for the 2018 Honda Odyssey
• The single biggest difference between Draw-Tite trailer hitch # 76170 and the etrailer hitch # e98855 for the 2018 Honda Odyssey is visibility. With Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" Item # 76170, which is the one I recommend, only the receiver will be visible. If you want the most hidden trailer hitch for your van this is the best option. Compare that to etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" # e98855...
  view full answer...


• Comparison Of Curt Class lll Trailer Hitches For 2006 Chevrolet Silverado 1500
• If your 2006 Silverado is a 1500, then the # 13322 and # 13332 are both designed to fit your truck. The difference between the two hitches is the 13322 has a round tube design, and the 13332 is made with a square tube. Both hitches have the same capacities and are Class lll hitches with a 2 inch receiver opening. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with...
  view full answer...


• Availability of Adjustable 2-Inch Ball Mount with 2-Inch Hitch Ball
• We do offer a range of adjustable ball mounts that have a 2-inch hitch ball and fit a 2-inch hitch, such as Curt # C45900 and the others shown on the included link. This Curt mount adjusts from a 6-inch drop to a 5-1/4-inch rise in 1-inch increments. Please refer to the linked video. In order to make your ball mount height adjustment as you exit and re-enter your driveway you will need to stop and secure the trailer and either decouple it, or if you are very handy with operating your tongue...
  view full answer...